Earthing Elite Mattress Cover Kits

Step 1: Check Your Outlets Are Earthed with our Socket Tester

In order to use your Earthing product, you must connect it to the “earth port” of an earthed 3 prong outlet (PowerPoint). Before plugging in your Earthing product, check that the outlet is earthed by plugging in the Socket Tester.

Three orange lights illuminated is GOOD and means that you have a proper earth and you are ready to connect your Earthing product. Any other light combination means your outlet is NOT properly earthed. Try testing another outlet. If it still doesn’t work, then you will need to use a grounding rod in the optional step 2 below.

Please Note: In Australia, it is compulsory by law to have all electrical power outlets Earthed, however, if in doubt for any reason it is easy to check with our socket tester which is inclusive in all our Starter Packs, otherwise you can purchase individually – please click here to order.

Step 2: (Optional) Using A Ground Rod When Outlets Aren't Earthed

a. First Push the Ground Rod directly into the earth around 20cm to 25cm, close to the foundation of the building and where vegetation is growing or the area is damp.

b. Run the cord from the Ground Rod, under or around a window or door, near where you will be using your product.

c. Make sure to cover the cord to prevent tripping.

d. Plug the prong end of your cord into the receptacle end of the Ground Rod cord. If you live in a dry area, such as a desert, soak the earth around the Ground Rod from time to time for maximum conductivity. You can order your ground rod here.

Step 3: Setting Up The Mattress Cover

a. Place the mat on your mattress, where it will be directly under a fitted sheet. The smooth, leather-like material should be directly under the sheet – this is the conductive side. Use the corner straps to secure the mat directly to your mattress and to hold it in place.

b. Insert the pin end of the Earthing cord into the adapter plug supplied, then the plug into a properly earthed wall outlet. Power does not need to be switched on.

c. Connect the snap end of the Earthing cord to the press stud on the mat.

d. Test the Mattress Cover with the product continuity tester to make sure the green light comes on and everything is connected.

e. Replace your standard fitted sheet.

f. When you lie down on the bed sheet, it may take several minutes for Earthing to take place depending on your perspiration level, the thickness of clothes or sheet and your hydration levels.

Step 4: How To Test For Conductivity With The Product Continuity Tester:

The purpose of the tester is to verify that your Earthing mat is conductive. The Product Tester is an Optional Accessory - you can order here.

a. Firstly verify that the Product Tester itself is operational by pressing the button that says “press” and release—the small light on the front will flash green one time then goes off. Indicates tester is good. If no green light battery (Lithium CR2032) may be flat or unit faulty.

b. Snap Coil Cord included onto Product Tester’s metal press stud, if not already assembled.

c. Insert your Earthing Adapter Plug into the power outlet you intend to use with your product.

d. Insert prong end of Product Tester Cord into one receptacle of the adapter plug

e. Plug Earthing cord from Mattress Cover into the other receptacle. You should now have both the Earthing Mattress Cover and Tester connected to the plug that is in a power outlet.

f. Place product tester flat on the cover. The round metal plate must be in contact with the surface of the mat. Press firmly on the mat to obtain a good contact and press down on the "Press" button. A green light means that the sheet is in working order. In the unlikely case that no green light comes on, the mat may be defective or has lost conductivity and should be replaced – you should also check your connecting cords to make sure they are conductive as well (see below). Sometimes, people have difficulty testing their products. If the light doesn’t come on, place one hand on the mat while holding the tester in the other hand and with one finger on the silver button on the back of tester. A green light would show that the body is grounded when touching the matt. Make sure that both the tester and the mat are plugged into the earth, as described above. The reason for perhaps the light not going on: you aren't pressing hard enough on the tester. You can also put some moisture on your fingertips to create better contact.

g. Disconnect product tester from the adapter plug. However, it is fine to leave plugged in to test when needed later on .

Step 6: How Care For Your Earthing Sleep Mat

Our conductive black carbon material is inherently antimicrobial and can be wiped down with a damp cloth. For a monthly deeper clean, we recommend a simple 3-step process:

1. Wipe down your product using a damp cloth mixed with a small amount of mild household soap to strip body sweat and natural skin oils.

2. Use a clean, damp cloth to thoroughly wipe away the soap. This prevents buildup, which blocks conductivity.

3. Let your product air dry. Important:

Never use a cleaning agent containing bleach, disinfectants, oils, whitening agents, or furniture polish as they can ruin the conductivity of your Earthing® product. Never put your product in the washing machine or soak in a tub.

Your Mattress Cover should be kept flat with no creases and if a heavy sleeper it may be advisable to rotate on a regular basis.

Sizes:

• California King 183 x 213
• King 193 x 203
• Queen 152 x 203
• Double 137 x 200
• King Single 99 x 203
• Single 99 x 190

Kit Includes:

• 1 x Mattress Cover of your choice
• 1 x Connection Cord
• 1 x Earthing Plug
• 1 x Instructions

 

Split King Kit Includes: 

• 2 x Single King Mattress Covers
• 2 x Connection Cords
• 1 x Earthing Plug
• 1 x Instructions

SKU	MC
Brand	Earthing
Shipping Weight	0.8500kg

90 Day Trial Period

12 Month Manufacturers Warranty